Construction Chemical Raw Materials
Raw materials and additives for dry-mix mortars, tile adhesives, concrete admixtures, waterproofing systems and coatings — sourced from verified Turkish suppliers and matched to your formulation and application.
Start a sourcing requestChat with us on WhatsApp
Products we can source for you.
HPMC & Cellulose Ethers
High-performance additives for water retention and workability in dry-mix mortars and adhesives.
Redispersible Polymer Powder (RDP)
Polymer powders that improve bonding, flexibility and durability of cement-based products.
Acrylic Binders & Coating Resins
Binders and resins for waterproofing membranes, paints and protective coatings.
Admixtures
Superplasticizers and defoamers for better workability, higher strength and stable concrete performance.
Fillers & Mineral Powders
Calcium carbonate, limestone and quartz powders in defined grades and particle sizes.
Polyurethane & Sealant Raw Materials
Raw materials for PU sealants, grouts, repair mortars and waterproofing chemicals.
Detailed Product Guide
Open any category below for technical descriptions, product lists, applications and answers to common sourcing questions.
01HPMC & Cellulose Ethers
Hydroxypropyl methylcellulose (HPMC) and related cellulose ethers are the most important performance additives in modern dry-mix mortars. Added at fractions of a percent, they retain water in the mortar so that cement can hydrate properly, improve workability and open time, and prevent sagging on vertical surfaces. Importers searching for an HPMC and RDP supplier often start here, and ARAZTA helps them reach Turkish suppliers, compounders and distributors who can offer consistent grades.
The right grade depends on the application. Viscosity, typically stated in mPa·s, controls water retention and thickening, while degree of substitution, particle size and dissolution behaviour affect mixing and performance in hot or cold conditions. Tile adhesives, cement renders, gypsum plasters, skim coats, self-levelling compounds and external insulation systems each need a different profile. ARAZTA gathers your formulation target, requests technical data sheets and samples from several suppliers, and arranges a comparison of viscosity, moisture content, ash content, pH and packaging before you commit to a volume order.
Because performance can vary between batches, we also ask about quality control, certificates of analysis and the supplier’s ability to deliver the same grade repeatedly. Typical packaging is 25 kg multi-wall paper bags on pallets, shipped by container. We coordinate sampling, documentation, export paperwork and shipment from Istanbul and other Turkish ports, so your production team receives the same grade, in the same packaging, order after order.
Key products
- HPMC 40,000 mPa·s — medium viscosity grade for gypsum plaster and skim coats.
- HPMC 75,000 mPa·s — general-purpose grade for tile adhesives and renders.
- HPMC 100,000 mPa·s — high water retention grade for cement-based adhesives.
- HPMC 150,000 mPa·s — high viscosity grade for thick-bed and insulation mortars.
- HPMC 200,000 mPa·s — very high viscosity grade for demanding adhesives.
- HEMC — hydroxyethyl methylcellulose with good water retention and open time.
- HEC — hydroxyethyl cellulose for paints, putties and thickening systems.
- Anti-sag modified HPMC — grade designed for heavy tiles and vertical application.
- Quick-dissolving HPMC — surface-treated grade for fast, lump-free mixing.
- Retarded-dissolution HPMC — grade for controlled viscosity build-up in mortars.
- Gypsum-grade HPMC — grade matched to gypsum plasters and joint fillers.
Typical applications
- Cement-based tile adhesives
- Gypsum plasters and joint compounds
- Cement renders and skim coats
- Self-levelling floor compounds
- External thermal insulation composite systems (ETICS)
- Wall putties and repair mortars
Benefits of sourcing through ARAZTA
- Grade selection: we help match viscosity and modification to your formulation and climate.
- Sample-first process: we obtain samples and technical data sheets before volume orders.
- Batch consistency: we ask suppliers about certificates of analysis and quality control.
- Container-ready export: we coordinate palletised packing and shipment from Istanbul.
Frequently asked questions
What viscosity of HPMC do I need for tile adhesive?
Tile adhesives commonly use medium to high viscosity grades, often in the 75,000 to 100,000 mPa·s range, but the best choice depends on your formulation. We can obtain samples of several grades for testing.
Can you supply HPMC samples before a large order?
Yes. We request samples and technical data sheets from suppliers so your laboratory can test them against your formulation before a volume purchase.
How is HPMC usually packed and shipped?
Typically in 25 kg multi-wall paper bags on pallets, loaded into 20-foot or 40-foot containers. We confirm packing and loading plans with the supplier.
Do you supply HPMC together with RDP?
Yes. Many importers request HPMC and RDP together, and we can combine both, along with fillers and admixtures, in a single coordinated sourcing request.
02Redispersible Polymer Powder (RDP)
Redispersible polymer powder (RDP) is a free-flowing powder made by spray-drying polymer emulsions. When water is added to a dry-mix mortar, the particles redisperse and, as the mortar cures, form a flexible polymer film that binds the mineral particles together. This improves adhesion to difficult substrates, flexibility, abrasion resistance, water impermeability and freeze-thaw durability. For importers evaluating a Turkish chemical raw materials exporter for polymer powders, ARAZTA acts as the technical and commercial bridge.
RDP is not a single product. Vinyl acetate-ethylene (VAE) powders are widely used in tile adhesives, renders and repair mortars, while acrylic and styrene-acrylic powders suit specialised systems. Glass transition temperature, minimum film-forming temperature, protective colloid, ash content and bulk density all influence performance and cost. ARAZTA collects your target application, for example a C2 tile adhesive, a flexible waterproofing slurry or an insulation base coat, and requests suitable grades with data sheets and samples.
Quality control matters because RDP performance can vary between suppliers and batches. We ask about production sources, certificates of analysis, storage stability and anti-caking behaviour, and support comparative laboratory testing by arranging samples. Standard packaging is 25 kg paper bags, shipped palletised in containers. We coordinate documentation, export clearance and shipment from Istanbul so that production plants receive consistent powder, ready to use in their dry-mix lines.
Key products
- VAE redispersible powder, general purpose — for tile adhesives and renders.
- VAE redispersible powder, flexible — for flexible tile adhesives and grouts.
- VAE redispersible powder, hydrophobic — for water-repellent renders and plasters.
- Acrylic redispersible powder — for high-alkali resistance and outdoor systems.
- Styrene-acrylic powder — for cost-effective repair and levelling mortars.
- Powder for ETICS base coats — for adhesive and reinforcing mortars in insulation systems.
- Powder for self-levelling compounds — for flow, smoothness and surface strength.
- Powder for waterproofing slurries — for flexible cementitious membranes.
- Powder for repair mortars — for bonding, shrinkage reduction and durability.
- Powder for skim coats and putties — for adhesion and crack resistance.
- Powder for flexible tile grouts — for flexibility and reduced water absorption.
Typical applications
- C1 and C2 tile adhesives
- Flexible cementitious waterproofing
- External insulation adhesives and base coats
- Repair and reprofiling mortars
- Self-levelling floor screeds
- Decorative renders and plasters
Benefits of sourcing through ARAZTA
- Application-led selection: we start from your end product, not just a product name.
- Technical comparison: we compare Tg, MFFT, ash content and packaging across suppliers.
- Testing support: we arrange samples so you can run laboratory trials before ordering.
- Reliable supply: we coordinate documentation and containerised shipment from Istanbul.
Frequently asked questions
What is the difference between RDP and acrylic binder?
RDP is a dry powder added to dry-mix mortars, while acrylic binder is a liquid emulsion used in paints, primers and waterproofing coatings. We can source both through Turkish suppliers.
Which RDP is used for C2 tile adhesive?
C2 adhesives usually use a high-quality VAE powder, but the exact grade depends on your formulation and test requirements. We can obtain several grades and data sheets for trials.
What is the shelf life of RDP?
Typically around 12 months when stored dry in unopened bags, but this varies by grade. We ask suppliers to state shelf life and storage conditions.
Can you find an RDP supplier for container-size orders?
Yes. We can request quotations for full container loads, including palletised packing and delivery terms to your port.
03Acrylic Binders & Coating Resins
Acrylic binders and coating resins are the film-forming heart of paints, primers, waterproofing membranes, sealers and protective coatings. They are supplied as water-based emulsions, solvent-based solutions or powders, and they determine adhesion, flexibility, water resistance, UV stability and durability. For importers who need an acrylic binder and coating resin supplier in Türkiye, ARAZTA helps connect formulation requirements with Turkish manufacturers and distributors that can support them.
Selection starts with the end product. A one-component acrylic waterproofing membrane needs good elongation and low water uptake, a masonry primer needs penetration and adhesion, and an exterior paint needs weathering resistance and a balanced glass transition temperature. Pure acrylic, styrene-acrylic and vinyl-acrylic emulsions differ in cost and performance. ARAZTA gathers your target properties, such as solids content, viscosity, pH, minimum film-forming temperature, particle size and the presence of surfactants or preservatives, and requests data sheets and samples from several suppliers.
Quality assurance includes certificates of analysis, batch traceability, storage stability, freeze-thaw behaviour and packaging suitable for liquid products. Emulsions are normally shipped in 200 kg drums, 1,000 litre IBC containers or tankers, and we coordinate the packing and documents required for liquid chemicals, including safety data sheets. We then manage export clearance and shipment from Turkish ports, giving formulators a dependable route to resins that perform consistently in their paints and coatings.
Key products
- Pure acrylic emulsion — premium binder for exterior paints and flexible coatings.
- Styrene-acrylic emulsion — cost-effective binder for interior paints and primers.
- Vinyl-acrylic emulsion — economical binder for interior wall paints and putties.
- Acrylic waterproofing binder — elastic binder for one-component roof and wall membranes.
- Acrylic primer binder — deep-penetrating binder for masonry and concrete primers.
- Acrylic sealer resin — resin for protective sealers on concrete and stone.
- Textured coating binder — binder for decorative and structural wall coatings.
- Elastomeric acrylic binder — high-elongation binder for crack-bridging coatings.
- Acrylic adhesive emulsion — binder for tile, flooring and construction adhesives.
- Water-based acrylic resin — low-VOC resin for architectural coatings.
- Solvent-based acrylic resin — resin for fast-drying industrial and floor coatings.
Typical applications
- Exterior and interior wall paints
- Roof and wall waterproofing membranes
- Masonry, concrete and wood primers
- Protective sealers for concrete and stone
- Decorative textured coatings
- Construction and flooring adhesives
Benefits of sourcing through ARAZTA
- Formulation-led requests: we translate solids, viscosity and film properties into clear supplier requests.
- Multiple options: we compare pure acrylic, styrene-acrylic and vinyl-acrylic offers.
- Liquid-chemical logistics: we coordinate drums, IBCs, safety data sheets and export documents.
- Consistent quality: we ask for certificates of analysis and batch traceability.
Frequently asked questions
What is the difference between pure acrylic and styrene-acrylic binders?
Pure acrylic binders offer better UV and weather resistance and are used in premium exterior systems. Styrene-acrylic binders are more economical and suit interior and less demanding uses.
Can you source binders for waterproofing membranes?
Yes. We can request elastic acrylic binders designed for one-component roof and wall waterproofing, together with data sheets and samples.
How are acrylic emulsions packed for export?
Usually in 200 kg drums or 1,000 litre IBC containers, sometimes in flexitanks or tankers. We confirm packing, labelling and safety documents with the supplier.
Do the binders comply with low-VOC requirements?
Many water-based acrylic binders are low in volatile organic compounds. State your VOC and regulatory requirements so we can verify them with each supplier.
04Admixtures
Concrete admixtures are chemical additives that change the behaviour of fresh and hardened concrete without changing its basic composition. For ready-mix producers, precast plants and contractors, the right admixture can reduce water demand, increase strength, extend workability during hot-weather transport, accelerate setting in cold weather or improve durability. Importers searching for a concrete admixtures supplier will find a broad range of Turkish producers, and ARAZTA helps compare them.
The main families are polycarboxylate ether (PCE) superplasticizers, naphthalene and melamine-based high-range water reducers, lignosulfonate plasticizers, set retarders, accelerators, air-entraining agents, shrinkage reducers, corrosion inhibitors and integral waterproofers. Each must be matched to the cement type, aggregates, mix design, ambient temperature and required slump retention. ARAZTA collects these details, asks suppliers for data sheets that state the relevant standard, such as EN 934-2 or ASTM C494, and arranges trial quantities for laboratory or plant testing.
Dosage, compatibility with other additives and chloride and alkali content are important quality indicators, and we include them in the supplier comparison. Admixtures are normally supplied in 20 kg or 200 kg drums, 1,000 litre IBC containers or bulk tankers, and some products are available as powders. We coordinate packing, safety data sheets, export documents and shipment from Istanbul and other Turkish ports, giving concrete producers a stable route to the admixtures their mix designs depend on.
Key products
- PCE superplasticizer, high range — for high-strength and self-compacting concrete.
- PCE with slump retention — for long-distance transport and hot weather.
- Naphthalene-based superplasticizer — economical high-range water reducer.
- Lignosulfonate plasticizer — normal-range water reducer for general concrete.
- Set retarder — for hot-weather concreting and large pours.
- Concrete accelerator — for cold weather and early strength development.
- Air-entraining admixture — for freeze-thaw resistant concrete.
- Shrinkage-reducing admixture — for reduced cracking in slabs and screeds.
- Integral waterproofing admixture — for water-resistant concrete and mortars.
- Corrosion inhibitor — for reinforced concrete exposed to chlorides.
- Defoamer and form-release agent — for surface quality and entrained air control.
Typical applications
- Ready-mix and precast concrete
- High-strength and self-compacting concrete
- Hot-weather and cold-weather concreting
- Shotcrete and tunnel linings
- Screeds, grouts and repair mortars
- Marine and infrastructure concrete
Benefits of sourcing through ARAZTA
- Trial quantities: we arrange samples so your laboratory can test admixtures with your cement.
- Standard-based comparison: we ask for data sheets referencing EN 934-2 or ASTM C494.
- Technical clarity: we compare dosage, solids, chloride and alkali content across offers.
- Bulk and drum options: we coordinate drums, IBCs and bulk shipments from Istanbul.
Frequently asked questions
Which concrete admixtures can be sourced from Türkiye?
We can source PCE and naphthalene superplasticizers, plasticizers, retarders, accelerators, air entrainers, shrinkage reducers, waterproofers and corrosion inhibitors from Turkish suppliers.
How do I choose between PCE and naphthalene superplasticizers?
PCE gives higher water reduction and better slump retention and is preferred for high-performance concrete. Naphthalene products are more economical for standard mixes. We can obtain trial samples of both.
Can admixtures be shipped in bulk?
Yes. Besides drums and IBC containers, some suppliers can arrange bulk or flexitank shipments. We confirm the option that fits your volume and receiving facilities.
Do the products meet international standards?
Many Turkish producers test to EN 934-2 or ASTM C494. We ask suppliers for certificates and test reports relevant to your market.
05Fillers & Mineral Powders
Fillers and mineral powders make up the largest share by weight of many construction products, and their particle size, whiteness, purity and moisture content strongly influence quality and cost. Calcium carbonate, limestone, dolomite and quartz powders are used in dry-mix mortars, adhesives, putties, paints, sealants and floor systems. Türkiye has abundant carbonate and quartz resources and a well-developed natural stone industry, which makes it an interesting origin for importers, and ARAZTA helps you reach the right Turkish suppliers.
Specifications are expressed in measurable terms: calcium carbonate content, particle size distribution such as D50 or mesh, brightness, oil absorption, moisture, acid insolubles and, for quartz, silica content and iron content. Coated and uncoated grades behave differently in paints and sealants. ARAZTA defines the specification with you, requests samples and certificates of analysis from several producers and compares them on grade, consistency, packaging and delivered cost, which is especially important for heavy, low-value materials.
Because freight is a large part of the final price, we look carefully at packing and loading. Powders can be supplied in 25 kg bags, 1,000 kg big bags or bulk containers with liners, and sands in big bags or bulk. We coordinate sampling, quality documentation, export clearance and shipment from Turkish ports, helping dry-mix plants, paint manufacturers and sealant producers secure fillers that meet their specification and their budget.
Key products
- Ground calcium carbonate, coarse — for dry-mix mortars and concrete products.
- Ground calcium carbonate, fine — for paints, putties and sealants.
- Micronised calcium carbonate — ultra-fine filler for high-quality coatings.
- Coated calcium carbonate — stearic acid coated grade for sealants and plastics.
- Limestone powder — filler and extender for cement, mortars and blocks.
- Dolomite powder — filler for mortars, paints and flooring compounds.
- Marble powder — high-whiteness filler from natural stone processing.
- Quartz powder — silica filler for grouts, flooring and technical mortars.
- Quartz sand, graded — dried sand for tile adhesives and self-levelling compounds.
- Silica sand, washed — washed and dried sand for dry-mix production lines.
- Talc and kaolin — functional fillers for paints and specialty mortars.
Typical applications
- Dry-mix mortars and tile adhesives
- Paints, putties and primers
- Sealants and joint fillers
- Self-levelling and industrial flooring
- Concrete products and blocks
- Grouts and repair mortars
Benefits of sourcing through ARAZTA
- Specification control: we define particle size, purity and whiteness before you order.
- Delivered-cost comparison: we compare offers including packing, loading and freight.
- Documented quality: we ask for certificates of analysis and sample approval.
- Flexible packing: we coordinate bags, big bags and bulk container options.
Frequently asked questions
Which fillers are available from Turkish suppliers?
We can source calcium carbonate in several grades, limestone, dolomite, marble powder, quartz powder, silica sand, talc and kaolin from Turkish producers.
How is particle size specified?
Usually as D50 in microns for fine powders or as mesh or sieve ranges for coarser grades and sands. Provide your target so we can obtain matching offers.
Can fillers be shipped economically?
Yes. Big bags and bulk containers with liners reduce handling cost. We compare options and calculate delivered cost for your destination.
Can I get a sample of calcium carbonate?
Yes. We can request samples and certificates of analysis from suppliers so you can approve the grade before placing an order.
06Polyurethane & Sealant Raw Materials
Polyurethane (PU) sealants, waterproofing membranes, grouts and repair systems depend on a carefully balanced set of raw materials. Polyols, isocyanates, plasticizers, fillers, thixotropic agents, catalysts, adhesion promoters and moisture scavengers each contribute to cure speed, elasticity, durability and cost. For importers and formulators sourcing from Türkiye, ARAZTA helps connect sealant and PU system requirements with Turkish suppliers, compounders and distributors of these specialised raw materials.
A typical enquiry describes the target product, such as a one-component PU sealant for facade joints, a two-component waterproofing membrane or a polyurethane injection resin for leak repair. From there, ARAZTA identifies the raw material families, requests technical data sheets with hydroxyl value, NCO content, viscosity and moisture limits, and compares offers on quality, safety information and delivery terms. Silane-modified polymers, fumed silica, precipitated calcium carbonate, plasticizers and pigments can be included in the same request.
Many of these materials are classified as hazardous or moisture-sensitive, so we place strong emphasis on safety data sheets, labelling, dangerous goods regulations and appropriate packaging, typically 200 kg drums, 1,000 litre IBC containers or sealed pails. We coordinate documentation, export clearance and shipment from Istanbul and other Turkish ports, with attention to storage and temperature conditions. The result is a compliant supply route for the raw materials behind durable, flexible and watertight building products.
Key products
- Polyether polyols — base polyols for sealants, membranes and foams.
- Polyester polyols — higher-strength polyols for adhesives and coatings.
- MDI and TDI isocyanates — isocyanate components for PU systems, subject to dangerous goods rules.
- PU prepolymers — ready-made prepolymers for one-component sealants.
- Silane-modified polymers — polymers for isocyanate-free hybrid sealants.
- Plasticizers — phthalate-free and conventional plasticizers for flexibility control.
- Fumed silica — thixotropic agent for non-sag sealants.
- Precipitated calcium carbonate — reinforcing filler for sealants and adhesives.
- Catalysts — tin and amine catalysts for cure speed control.
- Adhesion promoters — silane coupling agents for substrate bonding.
- Moisture scavengers and UV stabilizers — additives for shelf life and weathering resistance.
Typical applications
- Facade, window and expansion joint sealants
- Roof, balcony and terrace waterproofing
- Injection resins for leak sealing
- Flooring and industrial coatings
- Construction adhesives
- Grouts and repair systems
Benefits of sourcing through ARAZTA
- Safety-first sourcing: we check safety data sheets and packaging for hazardous raw materials.
- Complete formulation requests: we can combine polyols, fillers, additives and plasticizers in one request.
- Technical comparison: we compare hydroxyl value, NCO content and viscosity across suppliers.
- Compliant logistics: we coordinate labelling, drums, IBCs and export documents from Istanbul.
Frequently asked questions
Can you source raw materials for PU sealants from Türkiye?
Yes. We can approach Turkish suppliers for polyols, prepolymers, plasticizers, fillers, thixotropic agents, catalysts and additives used in PU and hybrid sealants.
Are hazardous raw materials such as isocyanates shipped by you?
Hazardous materials require special classification, packaging and carriers. We coordinate documentation and compliant shipment where suppliers and regulations allow.
What is an MS or silane-modified polymer sealant?
It is a hybrid sealant based on silane-modified polymers that cures with moisture without isocyanates. We can source the polymers and related additives.
What information is needed for a quotation?
The target product, performance requirements, required quantities, packaging and destination. Existing data sheets or formulations help suppliers respond precisely.
Why Source from Türkiye
Türkiye sits at the crossroads of Europe, Asia and the Middle East, and that position makes it a practical origin for construction chemical raw materials. For importers comparing options for construction chemical raw materials from Türkiye, ARAZTA connects you with Turkish suppliers that already serve dry-mix, concrete, paint and sealant producers, and that understand export requirements. ARAZTA’s B2B sourcing Türkiye service researches and compares suppliers so that your technical team can focus on formulation and approval.
The Turkish construction sector is one of the largest in the region, and it has created a deep supply base for mortars, adhesives, waterproofing systems, admixtures and coatings. Manufacturers, compounders and distributors work to EN, ISO and ASTM test methods, many hold ISO 9001 certification, and exporters are familiar with technical data sheets, safety data sheets and certificates of analysis. ARAZTA verifies whether a company manufactures, blends or only trades a product, and asks for the documents your quality team needs.
Cost and availability are further advantages. Natural resources such as limestone, marble and quartz support competitive mineral powders, and short supply chains help keep delivered prices attractive. The Customs Union with the European Union eases trade in industrial goods, while shorter sea transit than from Far Eastern origins reduces lead time for buyers in Europe, the Middle East, Africa and the Black Sea region.
Logistics are well developed. Istanbul export shipments can move through Marmara ports including Ambarlı, through Kocaeli and Izmir on the Aegean, and through Mersin and Iskenderun on the Mediterranean, supported by road and rail connections. Turkish exporters regularly handle palletised bags, big bags, drums, IBC containers and bulk loads, and prepare commercial invoices, packing lists, certificates of origin and safety documentation for chemical cargoes.
Quality expectations are also well understood. Turkish producers of mortars, adhesives and coatings supply international contractors and distributors, so they are used to sharing technical data sheets, safety data sheets, certificates of analysis and batch records. Many are open to laboratory trials, private-label packing and customised grades. We turn this openness into a structured process: define the specification, collect samples, compare results and confirm the commercial terms before the first container is loaded.
Export experience is the final piece. We coordinate samples, laboratory trials, quotations and shipments, keeping each step documented. If your project also requires finishing products or technical hardware, we can source tiles, marble and architectural stone and industrial equipment and components through the same Istanbul-based process, so one partner can cover your wider construction materials Türkiye needs.
Frequently Asked Questions
Why source construction chemical raw materials from Türkiye?
Türkiye offers a large construction industry, mature dry-mix and admixture producers, local mineral resources, competitive pricing and short sea transit to Europe, the Middle East, Africa and the Black Sea region. ARAZTA helps you reach verified suppliers.
Who is an HPMC RDP supplier in Türkiye I can trust?
ARAZTA evaluates Turkish HPMC and RDP suppliers on production source, quality documents and samples, then presents a comparison so you can choose with confidence.
Which concrete admixtures supplier can you connect me with?
We can approach Turkish producers of PCE and naphthalene superplasticizers, retarders, accelerators, air entrainers and other admixtures, and arrange trial samples.
Are Turkish chemical raw materials suitable for the EU market?
Many Turkish suppliers work with EU customers. Regulatory requirements such as REACH and CLP documentation should be stated in your request so we can confirm them with each supplier.
How are chemical raw materials packed for export?
Powders are usually packed in 25 kg bags or 1,000 kg big bags, and liquids in 200 kg drums or 1,000 litre IBC containers. We confirm packing and documents with each supplier.
Can I order a small sample first?
Yes. We can request samples and technical data sheets so your laboratory can test materials before you place a container order.
What is the usual minimum order quantity?
It depends on the product. Samples and small lots may be available, while commercial orders are often a pallet, a drum or a full container load. We confirm this during quotation.
How do I start a request with you?
Use the request form on our website or send a WhatsApp message with the product, specification, quantity and destination. A data sheet or application description is enough to begin.
How we support you
- Selected Turkish suppliers
- Technical and commercial comparison
- Samples and documentation
What to send us
- Product name or grade and intended application
- TDS or target specification, if available
- Required quantity, packaging and destination
- Preferred documents: SDS, COA and certificates
Have a requirement? Send it for an initial review.
A product name, photo, TDS or RFQ is enough to start.
Start a sourcing requestChat with us on WhatsApp